Jump to content


 

Photo

How To Change Tip For Adjustable Driver Shaft


  • Please log in to reply
12 replies to this topic

#1 trustyrusty

trustyrusty

    Advanced Member

  • Members
  • PipPipPip
  • 139 posts

Posted 01 September 2018 - 11:15 AM

Hi

I have Taylormade tip and want to callaway tip. I have seen them for 25.00. Does it need a tool to unscrew and add, looks like a torque screw or something. But about 10 mm deep to get to screw inside shaft, don’t know if glue is used, but sure it could be. And I will need to remove old tip too. Easier to take to local pro 😀 I might want to go back to other shaft later thanks

Edited by trustyrusty, 01 September 2018 - 11:29 AM.

Driver: Taylormade R11s
3 Wood: Callaway Razr Black

3 Hybrid: 19 degree Tour Edge Exotics EX10 (195m)
3 Hybrid: 19 degree Taylormade R7 (185m)

Irons: 3-PW Titliest AP2 716
Wedges: Titleist Vokey 56, 60
Putter: Oddessy BIG T
Ball: Titleist Pro v1
Handicap: 2.5

 


#2 trustyrusty

trustyrusty

    Advanced Member

  • Members
  • PipPipPip
  • 139 posts

Posted 03 September 2018 - 11:16 AM

Anyone?

Driver: Taylormade R11s
3 Wood: Callaway Razr Black

3 Hybrid: 19 degree Tour Edge Exotics EX10 (195m)
3 Hybrid: 19 degree Taylormade R7 (185m)

Irons: 3-PW Titliest AP2 716
Wedges: Titleist Vokey 56, 60
Putter: Oddessy BIG T
Ball: Titleist Pro v1
Handicap: 2.5

 


#3 steve008

steve008

    Advanced Member

  • Members
  • PipPipPip
  • 567 posts
  • LocationBrisbane

Posted 03 September 2018 - 12:36 PM

Hi

I have Taylormade tip and want to callaway tip. I have seen them for 25.00. Does it need a tool to unscrew and add, looks like a torque screw or something. But about 10 mm deep to get to screw inside shaft, don’t know if glue is used, but sure it could be. And I will need to remove old tip too. Easier to take to local pro I might want to go back to other shaft later thanks

It would be extremely advisable to go to your local pro and tell him what you want done.

It is not difficult to pull the tip from a shaft and replace it with another provided you have the correct equipment.

Best leave it to the pro if you have no experience in this area.



#4 golfguy33

golfguy33

    Advanced Member

  • Members
  • PipPipPip
  • 2510 posts

Posted 03 September 2018 - 04:29 PM

You will need a graphite shaft puller to remove the old adaptor. Then clean up the tip section of the shaft and then fix a new adaptor with the appropriate glue. If you damage the original ferrule you will need to replace it and or if the linish marks on the shaft are outside the ferrule line then you'll have to use a longer ferrule to cover the marks on the shaft etc.
Make sure you purchase the correct diameter adaptor that fits your shaft because it's hard to put a .350 into a .335 bore !
Hope that helps and probably better if you give it to someone that knows how and what to do, rather than stuffing up the shaft.
Jon...
  • Bluethunda, Francie, GPJ_Longdriver and 1 other like this

#5 Francie

Francie

    Inaugural Member

  • Members
  • PipPipPipPipPipPipPipPipPip
  • 36202 posts
  • LocationMelbourne

Posted 03 September 2018 - 11:16 PM

You will need a graphite shaft puller to remove the old adaptor. Then clean up the tip section of the shaft and then fix a new adaptor with the appropriate glue. If you damage the original ferrule you will need to replace it and or if the linish marks on the shaft are outside the ferrule line then you'll have to use a longer ferrule to cover the marks on the shaft etc.
Make sure you purchase the correct diameter adaptor that fits your shaft because it's hard to put a .350 into a .335 bore !
Hope that helps and probably better if you give it to someone that knows how and what to do, rather than stuffing up the shaft.
Jon...

 

I knew you'd pop along at some stage.  ;)


Inaugural winner "Castlemaine" Vic ISG golf day 2009
Inaugural Victorian OOM Putting Champion - Long Island 2011
Inaugural ISG National Golf Champion - Queensland September 2012

Inaugural winner Casey Rotary Golf Day 2012 - Part of the 'Dream Team'
Hole In One - 7th Hole Portsea GC - 9/10/2012
Long drive "champion" - Stinks 3 club challenge - 22/9/2013

Shipwreck Coast Classic - B Grade Men Winner (Warrnambool) - 9/11/2013

Inaugural holder - ISG TBPNTHWAOOM trophy - 2015

Eagle - Par 4 - 18th at St. Andrews Beach - 1/9/2015​

Eagle - Par 4 - 3rd at Long Reef GC (NSW) - 18/9/2018
Holder - Brass yacht trophy - 2015

Player of the Year (VPGC) - 2015

Winner - ISG Tombstone event - Lang Lang - 4/9/2016

Half of 4BBB Champion team with Commish - 2016 National Event

Half of winning finalist - Doubles Match-play team (VPGC) - 2016

​Team member - Winners of Australian ...... Matchplay Championship - 18/11/2016

Veterans Champion (VPGC) - 2016 

​Best stroke score OTS - 77 - Gardiners Run GC - 11/11/2018

 

"If a foursome is pressing you, wave them through - and then speed up." - Deane Beman

 

http://www.golflink....k_No=3013311351

 

Lowest ever handicap - 7.5

 


#6 CaNadiAn MiCk

CaNadiAn MiCk

    Head of the asylum

  • Administrators
  • 14953 posts

Posted 04 September 2018 - 08:02 AM

You will need a graphite shaft puller to remove the old adaptor. Then clean up the tip section of the shaft and then fix a new adaptor with the appropriate glue. If you damage the original ferrule you will need to replace it and or if the linish marks on the shaft are outside the ferrule line then you'll have to use a longer ferrule to cover the marks on the shaft etc.
Make sure you purchase the correct diameter adaptor that fits your shaft because it's hard to put a .350 into a .335 bore !
Hope that helps and probably better if you give it to someone that knows how and what to do, rather than stuffing up the shaft.
Jon...

And how much would this type of service be?   You know "pulling someone's shaft?

 

 

Serious now- simple procedure and going rate from a golf shop somewhere?


Join iseekgolf.com on Facebook

Follow iseekgolf.com on Twitter

For golf industry news.

Handicap


#7 golfguy33

golfguy33

    Advanced Member

  • Members
  • PipPipPip
  • 2510 posts

Posted 04 September 2018 - 05:17 PM

And how much would this type of service be?   You know "pulling someone's shaft?

 

 

Serious now- simple procedure and going rate from a golf shop somewhere?

 

Not sure where you go to get your shaft pulled but I know the little shop afew doors up from me was closed down by the council last week.

Apparently for not having the right type of business registration papers to give any style of massage ?

Cost them $22K in fines, if that's the pricing that you're trying to ascertain Mads :)

 

Seriously though, to do the job is about $35 + adaptor + grip if required could run $100

 

Jon... 


  • voss and CaNadiAn MiCk like this

#8 Goldy

Goldy

    Ed Rayner's love child

  • Members
  • PipPipPipPipPipPipPipPipPip
  • 39050 posts
  • Location20m closer than you expected

Posted 04 September 2018 - 05:18 PM

Not sure where you go to get your shaft pulled but I know the little shop afew doors up from me was closed down by the council last week.

Apparently for not having the right type of business registration papers to give any style of massage ?

Cost them $22K in fines, if that's the pricing that you're trying to ascertain Mads :)

 

Seriously though, to do the job is about $35 + adaptor + grip if required could run $100

 

Jon... 

 

What are your sandbelt based customers going to do while they wait for the re-grip now?


  • voss, CaNadiAn MiCk and RobNewy like this

Winner Moonah Legends 2013 ISG Nationals | Winner The National 2013 ISG Nationals | Winner 4BBB 2013 ISG Nationals
Winner Stink's 3 Club Challenge 2015 | Winner C grade OOM The Sands 2016

Hole-in-one Growling Frog 14/1/17 5th hole 137m TM RBZ 5 hybrid, Srixon AD333 ball | Growling Frog GC Matchplay Champion 2017

Winner B grade OOM Curlewis 2018

Other, less impressive stuff...(I know...it's marginal...)
R/Up ISG Nationals 2013 | C Grade LD Growling Frog 8/2/14, 11th hole, TM R1, HOF Patriot shaft, testicles of steel | NTP 2nd hole Kooindah Waters 2014 ISG Nationals

3 Birdies in one round The Glades 2015 ISG Nationals | R/Up 4BBB 2015 ISG Nationals | NTP 16th hole Growling Frog OOM 2017 

C Grade LD Growling Frog 26/12/17, 15th hole, Callaway BB Alpha, HOF Patriot shaft, same old testicles of steel
C Grade LD Growling Frog 11/8/18, blah blah blah,,,,this is getting to be almost monotonous..... 

C Grade LD Growling Frog 1/9/18,...maybe these are now so commonplace I should just stop listing them

NTP Yering Meadows 25th hole 1/12/18

Never contended for the trophy named for me

 

Low Handicap point 12.7 9/4/16

Finally...and most importantly...
Smoldy....when only the best will do.


#9 trustyrusty

trustyrusty

    Advanced Member

  • Members
  • PipPipPip
  • 139 posts

Posted 05 September 2018 - 06:35 PM

I know someone that has it done for $30.00 I will do that.. easy 😀

Driver: Taylormade R11s
3 Wood: Callaway Razr Black

3 Hybrid: 19 degree Tour Edge Exotics EX10 (195m)
3 Hybrid: 19 degree Taylormade R7 (185m)

Irons: 3-PW Titliest AP2 716
Wedges: Titleist Vokey 56, 60
Putter: Oddessy BIG T
Ball: Titleist Pro v1
Handicap: 2.5

 


#10 davidjren

davidjren

    Suspect

  • Members
  • 4 posts
  • LocationNYC

Posted 05 September 2018 - 07:35 PM

I know someone that has it done for $30.00 I will do that.. easy

Who's make it with 30.000$ ? 



#11 trustyrusty

trustyrusty

    Advanced Member

  • Members
  • PipPipPip
  • 139 posts

Posted 06 September 2018 - 05:44 PM

I will find out if you pm me. I know it was done for that ..

Driver: Taylormade R11s
3 Wood: Callaway Razr Black

3 Hybrid: 19 degree Tour Edge Exotics EX10 (195m)
3 Hybrid: 19 degree Taylormade R7 (185m)

Irons: 3-PW Titliest AP2 716
Wedges: Titleist Vokey 56, 60
Putter: Oddessy BIG T
Ball: Titleist Pro v1
Handicap: 2.5

 


#12 Tango67

Tango67

    Advanced Member

  • Members
  • PipPipPip
  • 785 posts
  • LocationMacau

Posted 02 October 2018 - 09:34 PM

YouTube has plenty of videos on it

#13 voss

voss

    Advanced Member

  • Members
  • PipPipPip
  • 1648 posts

Posted 16 October 2018 - 09:55 AM

Not sure where you go to get your shaft pulled but I know the little shop afew doors up from me was closed down by the council last week.
Apparently for not having the right type of business registration papers to give any style of massage ?
Cost them $22K in fines, if that's the pricing that you're trying to ascertain Mads :)
 
Seriously though, to do the job is about $35 + adaptor + grip if required could run $100
 
Jon...


And I thought you were just on a 'coffee' break last time I visited :)




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users